User Tools
single_small_ccd_module_support
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| single_small_ccd_module_support [2025/07/30 08:09] – [Single Small CCD Module Support] simon | single_small_ccd_module_support [2025/07/30 08:33] (current) – [Table] simon | ||
|---|---|---|---|
| Line 28: | Line 28: | ||
| ^ ::: | Container Botttom | ^ ::: | Container Botttom | ||
| ^ ::: | 30 cm long CCD Flex Cable | Flex cable | 1 | No | 0.006 | Capton | ^ ::: | 30 cm long CCD Flex Cable | Flex cable | 1 | No | 0.006 | Capton | ||
| + | |||
| + | ==== Assembly ==== | ||
| + | ^ Single Small CCD Frame | ||
| + | ^ Step ^ Part ^ No. ^ Weight (kg) | | | ||
| + | ^ 1st Step | ||
| + | | ::: | 4-40 UNC x 3/8 Inch Socket Countersunk Nylon Screws (ASME B18.3) | ||
| + | | ::: | M1.6x5 Cross Recessed flat countersunk head Screw | 10 | 0.001 | | | ||
| + | | ::: | Rectangular CCD Frame Spacer | ||
| + | | ::: | Cylindrical CCD Frame Spacer | ||
| + | | ::: | Al2O3 Insulator | ||
| + | | ::: | Heater Assembly | ||
| + | | ::: | Small CCD Top Support Frame | 1 | 0.220 | | | ||
| + | | ::: | Small CCD Bottom Support Frame | 1 | 0.004 | | | ||
| + | | Total: || 23 | 0.662 | | | ||
| + | ^ 2nd Step | Single Small CCD Assembly | ||
| + | | ::: | Single Small CCD Frame Assembly | ||
| + | | ::: | Temperature Sensor Housing | ||
| + | | ::: | Platinum Resistance Pt100 Wire-Wound Detector Element, 28 mm | 1 | 0.005 | | | ||
| + | | ::: | M3x8 Hex socket head cap screws fully threaded | ||
| + | | ::: | M3 Flat washers without chamfer | ||
| + | | ::: | Single Large CCD Module | ||
| + | | Total: || 6 | 0.875 | | | ||
| + | ^ 3rd Step | Small CCD Cryovessel Support Assembly | ||
| + | | ::: | Single Small CCD Assembly | ||
| + | | ::: | Cryostat Complete | ||
| + | | ::: | 4-40 UNC x 0.5625 Hex socket head cap screws, ANSI B18.3 | 6 | 0.001 | | | ||
| + | | Total: || 8 | 50.407 | ||
| + | | ||||| | ||
| + | ^ Small CCD Single Die Box ||||| | ||
| + | ^ 1st Step | M1.6 x 5 cross countersunk screws | ||
| + | | ::: | M2 x 12 cross countersunk screws | ||
| + | | ::: | M1 x 4 slotted cheese head screws | ||
| + | | ::: | Container Top | ||
| + | | ::: | Container Middle | ||
| + | | ::: | Container Bottom | ||
| + | | ::: | Retention Bar | ||
| + | | ::: | 3.5 mm M3 nitril ESD rubber plunger | ||
| + | | ::: | AlN CCD support PCB | ||
| + | | ::: | 30 cm long CCD Flex Cable | ||
| + | | Total: || | 18 | 0.19959 | ||
single_small_ccd_module_support.1753855792.txt.gz · Last modified: by simon
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
