User Tools
wiki
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| wiki [2026/02/14 22:09] – [Servers Configuration] vagelis | wiki [2026/02/15 21:06] (current) – [Network Configuration DAMIC@Zurich] vagelis | ||
|---|---|---|---|
| Line 77: | Line 77: | ||
| | Server 2 Internet | | Server 2 Internet | ||
| | Power PDU 4PS | 192.168.200.11 | | Power PDU 4PS | 192.168.200.11 | ||
| - | | Single Gauge TPG361 | + | | Single Gauge TPG361 |
| - | | HiCube | + | | HiCube |
| | HVPSU Kethley 2450 | 192.168.200.14 | | HVPSU Kethley 2450 | 192.168.200.14 | ||
| | LVPSU R&S HMP2040 | | LVPSU R&S HMP2040 | ||
| Line 86: | Line 86: | ||
| ==== Network Configuration DAMIC@Zurich ==== | ==== Network Configuration DAMIC@Zurich ==== | ||
| - | ^ Device | + | ^ Device |
| - | | Server 1 Intranet | + | | Server 1 Intranet |
| - | | Server 1 Extranet | + | | Server 1 Extranet |
| - | | Power PDU 4PS | 192.168.200.11 | 255.255.255.0 | 192.168.200.1 | 130.60.164.1 | PowerPDU-CF | admin | 1rChEL@PDU | + | | Power PDU 4PS |
| - | | Single Gauge Serial2LAN (EX-611-2) | 192.168.200.12 | 255.255.255.0 | 192.168.200.1 | 130.60.164.1 | TPG261 | + | | Single Gauge Serial2LAN (EX-611-2) |
| - | | HiCube | + | | HiCube |
| - | | HVPSU Kethley 2450 SourceMeter | + | | HVPSU Kethley 2450 SourceMeter |
| - | | LVPSU R&S HMP2030 | + | | LVPSU R&S HMP2030 |
| - | | Lakeshore 335 USB2LAN (DS-700) | + | | Lakeshore 335 USB2LAN (DS-700) |
| - | | ACM | 192.168.1.5 | + | | ACM |
| - | | | | + | |
| ===== Servers Configuration ===== | ===== Servers Configuration ===== | ||
| Line 117: | Line 115: | ||
| For storage, a 4 x 4TB hot-swap HDDs array, configured in RAID10 mode is used with the on-board intel RAID controller (Intel Rapid Storage Technology). This setup enables simultaneous writing to two hard drives (RAID1) and data mirroring to another two (RAID0). This configuration enhances writing speed and maintains a constant backup of the entire system. Each of the four 4TB hard drives contributes to an effective storage capacity of 8TB. | For storage, a 4 x 4TB hot-swap HDDs array, configured in RAID10 mode is used with the on-board intel RAID controller (Intel Rapid Storage Technology). This setup enables simultaneous writing to two hard drives (RAID1) and data mirroring to another two (RAID0). This configuration enhances writing speed and maintains a constant backup of the entire system. Each of the four 4TB hard drives contributes to an effective storage capacity of 8TB. | ||
| - | The system does not support UEFI, and access to full storage capacity is limited to operating systems supporting GPT architecture (>2TB volumes). The lack of UEFI limits Windows to MBR-only versions, and UNIX-type operating systems are recommended. For the operating system, Ubuntu 20.04.6 LTS was chosen due to its compatibility with LabVIEW (Q3 2022), the LTA and our image acquisition software. The default package manager is apt, while rpm is also present. | + | The system does not support UEFI and access to full storage capacity is limited to operating systems supporting GPT architecture (>2TB volumes). The lack of UEFI limits Windows to MBR-only versions and UNIX-type operating systems are recommended. For the operating system, Ubuntu 20.04.6 LTS was chosen due to its compatibility with LabVIEW (Q3 2022), the LTA drivers |
| For further information about our server please read the following [[pages]]. | For further information about our server please read the following [[pages]]. | ||
wiki.1771103382.txt.gz · Last modified: by vagelis
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
