User Tools
darma
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| darma [2025/07/21 13:28] – [DAMIC-M@Zurich] simon | darma [2025/07/21 13:33] (current) – [Single Small CCD Module Support] simon | ||
|---|---|---|---|
| Line 8: | Line 8: | ||
| * [[Single Large CCD Module Support|Single Large CCD Module Support]] | * [[Single Large CCD Module Support|Single Large CCD Module Support]] | ||
| * [[Single Small CCD Module Support|Single Small CCD Module Support]] | * [[Single Small CCD Module Support|Single Small CCD Module Support]] | ||
| - | ===== Cryostat ===== | ||
| - | For DAMIC-M@Zurich a new Cryostat was commissioned. It is based on the design of the AlpineCube by //P. Robmann//, the cryo- and vacuumsystem staied the same. It is heavely modified on the cryohead mounting and CCD holders/ | ||
| - | ---- | ||
| - | {{: | ||
| - | {{ : | ||
| - | ---- | ||
| - | |||
| - | ^ Name | ||
| - | | Cryostatbody | ||
| - | | Cryostat Door | {{ : | ||
| - | | Cryohead | ||
| - | | Cryostat Complete | ||
| - | | Insulator | ||
| - | | DB50 Pass Through Shield | ||
| - | | Door Flange | ||
| - | | Electronics | ||
| - | | Vacuuminterface | ||
| - | | Vacuum Fittings | ||
| - | | Vacuum Intake | ||
| - | | Cryohead Mount | {{ : | ||
| - | |||
| - | ==== BOM ==== | ||
| - | ^ Assembly | ||
| - | | | ||
| - | | | ||
| - | | Cryo-Head | ||
| - | | | Flat washers without chamfer, DIN 125, for M8 thread | ||
| - | | | Tube 104x2 mm - 136.1 mm length, 304 stainless | ||
| - | | | Mixed Refrigerant Gas Cryocooler - Mylar Wrapped | ||
| - | | | 90 K Blend Hoses, 1/4" [6mm] by 10' [3 m] | 2 | N/A | | ||
| - | | | Charging Kit - 17 Liter Bottle (MR-90 Blend) | ||
| - | | | ISO 100 Centering Ring with Outer Ring - 301062 | ||
| - | | | ISO-F Welding Flange, ISO 100 - 301079 | ||
| - | | | Cryo-Head Support Plane | 1 | 1.77 | | ||
| - | | | M6x25 Hex socket head cap screws fully threaded, ISO 4762 | 14 | 0.009 | | ||
| - | | | Flat washers without chamfer, DIN 125, for M6 thread | ||
| - | | | 180x5 mm O-ring (5 mm diameter, 565 mm length) | ||
| - | | | ||
| - | | VacUum Attachment | ||
| - | | | KF Tubulation, inner diameter 50 mm, 70 mm length | ||
| - | | | Vacuum Seal Cover | 1 | 3.09 | | ||
| - | | | M6x25 Hex socket head cap screws fully threaded, ISO 4762 | 16 | 0.009 | | ||
| - | | | Flat washers without chamfer, DIN 126, for M6 thread | ||
| - | | | 254x5 mm O-Ring NBR 770 ( mm diameter, 799 mm length) | ||
| - | | | ||
| - | | External Cryostat Hardware | ||
| - | | | GN 851 Hook Toggle Clamps | ||
| - | | | M4x14 Hexagon socket button head screw | 12 | 0.002 | | ||
| - | | | RS PRO Rubber Vibration Damper M10, Ø 85mm x 25mm, 40kg | 4 | 0.108 | | ||
| - | | | M7x14 Ultra-Low-Profile Socket Head Screw | 8 | 0.006 | | ||
| - | | | Articulating Constant Torque Hinge, Free Swinging, Bright | ||
| - | | | M4x25 Hex socket flat countersunk head screw | 8 | 0.004 | | ||
| - | | | ||
| - | | Passthrough Connectors | ||
| - | | | M3x30 Hex socket head cap partially threaded screw | 8 | 0.002 | | ||
| - | | | DB50 Feedthrough Connector for Vacuum Applications | ||
| - | | | DB50 Male HIVAC Adapter for Vacuum Applications | ||
| - | | | DB37 Feedthrough Connector for Vacuum Applications | ||
| - | | | DB37 Male HIVAC Adapter for Vacuum Applications | ||
| - | | | ||
| - | | Cryostat Body | Cryostat Door | 1 | 7.760 | | ||
| - | | | Cryostat Body | 1 | 22.950 | ||
| - | | | Door Cylindrical Flange | ||
| - | | | O-Ring ID 150 mm x 5.3 mm NBR 70 | 2 | 0.012 | | ||
| - | | | O-ring ID 373 mm x 5.25 mm CS NBR (length (1171.77 mm) | 1 | 0.0304 | ||
| - | | | O-ring ID 353 mm x 5.25 mm CS NBR (length 1110.363 mm) | 1 | 0.0288 | ||
| - | | | M5x25 Hex socket head cap screws fully threaded | ||
| - | | | ||
| - | | Internal Hardware | ||
| - | | | 4-40 UNC x 3/8 Inch Socket Countersunk Nylon Screws (ASME B18.3) | ||
| - | | | Al2O3 Insulator | ||
| - | | | Arcol AP830 Power Resistor 50Ω ±1% / 30W | 2 | 0.035 | | ||
| - | | | M6x6 Hex socket set screws with flat point | 2 | 0.001 | | ||
| - | | | Cryo-Head Heater Attachment | ||
| - | | | M3x8 Hex socket head cap screws fully threaded | ||
| - | | | M3 Flat washers without chamfer | ||
| - | | | M3 Slotted round nuts BN 1413 | 1 | 0.001 | | ||
| - | | | M3x8 Hex socket flat countersunk head screw | 1 | 0.001 | | ||
| - | | | Temperature Sensor Attachment | ||
| - | | | Platinum Resistance Pt100 Wire-Wound Detector Element, 28 mm | 2 | 0.0052 | ||
| - | | | ||
| - | | Electronics Assembly | ||
| - | | | DAMIC Font-End electronics Board V2.0 | 4 | ||
| - | | | Samtec Pass-through Board | 1 | ||
| - | | | Board Passthrough External Flange | ||
| - | | | Board Passthrough Internal Falge | 1 | 0.405 | | ||
| - | | | M4x20 Hex socket head cap screws fully threaded | ||
| - | | | O-Ring ID 150 mm x 5.3 mm NBR 70 | 1 | 0.012 | | ||
| - | | | Viton Fluoroelestimer O-Ring, nominal 3½” x 3/32, Dash No, 153 | 2 | 0.003 | | ||
| - | | | M5x25 Hex socket head cap screws fully threaded | ||
| - | | | ||
| - | | Additional Vacuum Hardware | ||
| - | | | KF Elbow 90°, DN 50 | 1 | 0.364 | | ||
| - | | | KF Tees, DN25 | 2 | 0.187 | | ||
| - | | | KF Flange with Pipe Thread, Female, DN25, NPT - Internal Thread | ||
| - | | | KF Centering Rings, O-Ring, DN50 | 3 | 0.027 | | ||
| - | | | KF Centering Rings, O-Ring, DN25 | 6 | 0.011 | | ||
| - | | | KF Tension Ring for Elastomer Gasket, DN50 | 3 | 0.157 | | ||
| - | | | KF Tension Ring for Elastomer Gasket, DN25 | 6 | 0.062 | | ||
| - | | | Conical Reducer, ISO-KF Flange Size NW50 to NW40 | 1 | 0.062 | | ||
| - | | | Low Pressure Proportional Relief Valve, 1/4 in. MNPT x 1/4 in. FNPT | 1 | 0.270 | | ||
| - | | | Bellows Sealed Valve, Welded, SS Stem Tip, 1/4 in. MNPT | 1 | 0.110 | | ||
| - | | | Safety Valve, NW50 ISO-KF, Vitron, 220 VAC 50/60 Hz | 1 | 1.800 | | ||
| - | | | ActiveLine-Gauge Mating connector, 6 pole | 1 | ||
| - | | | PKR 251, FPM-sealed, DN 25 ISO-KF | ||
| - | ==== Large CCD Bookcase Assembly ==== | ||
| - | To fully incorperate the DAMIC-M CCD Module a single Bookcase like CCD-Mount was developed, it is designed to hold up to four big DAMIC-M CCD Modules. The full list of Materials can be found {{ : | ||
| - | |||
| - | ^ Name ^ Assembly Diagramm | ||
| - | | Bookcase | ||
| - | | External Frame | {{ : | ||
| - | | Frames | ||
| - | | Support | ||
| - | |||
| - | ==== Single Large CCD Module Support ==== | ||
| - | Since the Large CCD Modules are quite expensive and hard to come by a single large Module holder was developed, it's BOM can be found {{ : | ||
| - | |||
| - | ^ Name ^ Assembly Diagramm | ||
| - | | Sides | ||
| - | | Assembly | ||
| - | |||
| - | ==== Single Small CCD Module Support==== | ||
| - | As a byproduct of the Large CCD Module production there are also very small CCD Modules, which are used in DARMA. For this small CCD we also developed a CCD Mounting case and a container. The two BOM can be found {{ : | ||
| - | |||
| - | ^ Name ^ Assembly Diagramm | ||
| - | | Frame | {{ : | ||
| - | | Container | ||
| - | | Flex | Not Available | ||
| - | | PCB | ::: | {{ : | ||
| - | | Assembly | ||
darma.1753097301.txt.gz · Last modified: by simon
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
