UZH

Physik-Institut

Physik-Institut DAMIC Wiki

User Tools

Site Tools

Trace: • lock-in_amplifiers • vacuum_controll • voltage_controll • wiki
acm_board

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
acm_board [2024/09/13 15:11] – [Software] simonacm_board [2024/11/15 14:06] (current) – simon
Line 1: Line 1:
-====== The ACM Board ======+====== The Acquisition and Control Module (ACM Board) ======
  
 Detail schematics of the board are available here: [[https://edg.uchicago.edu/~bogdan/DAMIC_ACM/schematics.html|ACM Schematics]]. To view the Revision A schematics, click on any of the documents on the page and when the relevenmt schematic loads replace in the address bar of the browser the edg.uchicago.edu/~bogdan/DAMIC_ACM/**doc**/.... with edg.uchicago.edu/~bogdan/DAMIC_ACM/doc/**docA**/... Detail schematics of the board are available here: [[https://edg.uchicago.edu/~bogdan/DAMIC_ACM/schematics.html|ACM Schematics]]. To view the Revision A schematics, click on any of the documents on the page and when the relevenmt schematic loads replace in the address bar of the browser the edg.uchicago.edu/~bogdan/DAMIC_ACM/**doc**/.... with edg.uchicago.edu/~bogdan/DAMIC_ACM/doc/**docA**/...
Line 22: Line 22:
 ===== Software ===== ===== Software =====
 The software for the ACM driver can be found here: The software for the ACM driver can be found here:
-  * /Home/ACM+  * /home/ccdtest/Desktop/ACM_Firmware
  
 To upload or update the firmware the auxiliary software //Quartus// is needed it is located here: To upload or update the firmware the auxiliary software //Quartus// is needed it is located here:
   * /intelFPGA_pro/24.2/quartus/bin   * /intelFPGA_pro/24.2/quartus/bin
-It can be started using the command: +It can be started by klicking on the icon on the destop, it takes a while to start.
-  * ./quartus+
 After quartus started go to the taskbar and go to //Tools// and click //Programmer//, a second window will open, where you can select the hardware setup and add files, after choosing the correct hardware (USB-Blaster 2-1.4) press start. The first window will show you messages related to the upload process. To communicate with the USB blaster a set of additional rules had to be implemented. First open/create the file ///etc/udev/rules.d/99-usb-blaster.rules// and add the following command: After quartus started go to the taskbar and go to //Tools// and click //Programmer//, a second window will open, where you can select the hardware setup and add files, after choosing the correct hardware (USB-Blaster 2-1.4) press start. The first window will show you messages related to the upload process. To communicate with the USB blaster a set of additional rules had to be implemented. First open/create the file ///etc/udev/rules.d/99-usb-blaster.rules// and add the following command:
   * SUBSYSTEM=="usb", ATTRS{idVendor}=="09fb", ATTRS{idProduct}=="6001", GROUP="usb>   * SUBSYSTEM=="usb", ATTRS{idVendor}=="09fb", ATTRS{idProduct}=="6001", GROUP="usb>
acm_board.1726233076.txt.gz · Last modified: by simon

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki