UZH

Physik-Institut

Physik-Institut DAMIC Wiki

User Tools

Site Tools

Trace: • lock-in_amplifiers • wiki • vacuum_controll
acm_board

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
acm_board [2024/09/02 11:57] – [Software Installation] simonacm_board [2024/11/15 14:06] (current) – simon
Line 1: Line 1:
-====== The ACM Board ======+====== The Acquisition and Control Module (ACM Board) ======
  
 Detail schematics of the board are available here: [[https://edg.uchicago.edu/~bogdan/DAMIC_ACM/schematics.html|ACM Schematics]]. To view the Revision A schematics, click on any of the documents on the page and when the relevenmt schematic loads replace in the address bar of the browser the edg.uchicago.edu/~bogdan/DAMIC_ACM/**doc**/.... with edg.uchicago.edu/~bogdan/DAMIC_ACM/doc/**docA**/... Detail schematics of the board are available here: [[https://edg.uchicago.edu/~bogdan/DAMIC_ACM/schematics.html|ACM Schematics]]. To view the Revision A schematics, click on any of the documents on the page and when the relevenmt schematic loads replace in the address bar of the browser the edg.uchicago.edu/~bogdan/DAMIC_ACM/**doc**/.... with edg.uchicago.edu/~bogdan/DAMIC_ACM/doc/**docA**/...
Line 22: Line 22:
 ===== Software ===== ===== Software =====
 The software for the ACM driver can be found here: The software for the ACM driver can be found here:
-  * /Home/ACM+  * /home/ccdtest/Desktop/ACM_Firmware
  
 To upload or update the firmware the auxiliary software //Quartus// is needed it is located here: To upload or update the firmware the auxiliary software //Quartus// is needed it is located here:
   * /intelFPGA_pro/24.2/quartus/bin   * /intelFPGA_pro/24.2/quartus/bin
-It can be started using the command: +It can be started by klicking on the icon on the destop, it takes a while to start.
-  * ./quartus+
 After quartus started go to the taskbar and go to //Tools// and click //Programmer//, a second window will open, where you can select the hardware setup and add files, after choosing the correct hardware (USB-Blaster 2-1.4) press start. The first window will show you messages related to the upload process. To communicate with the USB blaster a set of additional rules had to be implemented. First open/create the file ///etc/udev/rules.d/99-usb-blaster.rules// and add the following command: After quartus started go to the taskbar and go to //Tools// and click //Programmer//, a second window will open, where you can select the hardware setup and add files, after choosing the correct hardware (USB-Blaster 2-1.4) press start. The first window will show you messages related to the upload process. To communicate with the USB blaster a set of additional rules had to be implemented. First open/create the file ///etc/udev/rules.d/99-usb-blaster.rules// and add the following command:
   * SUBSYSTEM=="usb", ATTRS{idVendor}=="09fb", ATTRS{idProduct}=="6001", GROUP="usb>   * SUBSYSTEM=="usb", ATTRS{idVendor}=="09fb", ATTRS{idProduct}=="6001", GROUP="usb>
Line 35: Line 34:
 After this the setup has to be restarted for the modification to take effect.   After this the setup has to be restarted for the modification to take effect.  
 The firmware can be found here (installed is: damic_m_acm_v11a.sof): The firmware can be found here (installed is: damic_m_acm_v11a.sof):
-  * /Home/ACM/Firmware+  * /home/ccdtest/Desktop/ACM_Firmware/Firmware V1
  
 **Note:** After every shutdown (see above chapter) of the ACM board you have to upload the firmware again. **Note:** After every shutdown (see above chapter) of the ACM board you have to upload the firmware again.
acm_board.1725271022.txt.gz · Last modified: by simon

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki