phase1:phase1:bpixeltools
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
| phase1:phase1:bpixeltools [2015/02/20 17:13] – ngadiuba | phase1:phase1:bpixeltools [2015/05/21 11:36] – ngadiuba | ||
|---|---|---|---|
| Line 15: | Line 15: | ||
| Main general commands: | Main general commands: | ||
| + | * **scanccu** : returned the list of the connected CCUs | ||
| * **scanringedevice** : scan all the connected electronic devices and addresses (ccu, dohs, pohs, ... ) | * **scanringedevice** : scan all the connected electronic devices and addresses (ccu, dohs, pohs, ... ) | ||
| * **scanpixeldevice** : summary of the connected and missing devices (no addresses list) | * **scanpixeldevice** : summary of the connected and missing devices (no addresses list) | ||
| Line 24: | Line 25: | ||
| * **pohN read** : read the values of the 4 channels bias and gain (b0, b1, b2, b3, g0, g1, g2, g3) | * **pohN read** : read the values of the 4 channels bias and gain (b0, b1, b2, b3, g0, g1, g2, g3) | ||
| * to set the bias or the gain do for example: **pohN set b0 30** | * to set the bias or the gain do for example: **pohN set b0 30** | ||
| - | * to set all the values at the same time do for example: **pohN set all 3 3 3 3 0 0 0 0** | + | * to set all the values at the same time do for example: **pohN set all 3 3 3 3 0 0 0 0** |
| + | * to init the poh settings: **pohN init** | ||
| + | |||
| + | To test i2c speed: | ||
| + | |||
| + | * first set the ccu: **ccu 0x7b** | ||
| + | * set the channel (0x13 for L34 and 0x11 for L12): **channel 0x13** | ||
| + | * set the i2c speed: **i2cspeed 1000** | ||
| + | * NB: the programmable i2c speeds are 100, | ||
| + | |||
| + | ====Test Programs==== | ||
| Run the test program (from a different terminal): | Run the test program (from a different terminal): | ||
| Line 31: | Line 42: | ||
| cd test | cd test | ||
| | | ||
| + | |||
| + | Run the test program for POH bias scan at a specific gain | ||
| + | |||
| + | * open a terminal and run the ccu program | ||
| + | * open a second terminal and run the fed program | ||
| + | * open a third terminal for the test program: | ||
| + | |||
| + | cd TriDAS/ | ||
| + | | ||
| + | cd test | ||
| + | | ||
| + | |||
| + | * the results are stored in the testdata folder (create one if it does not exist) | ||
| + | |||
| + | Additional macro to plot the poh bias scan results in the folder " | ||
| + | |||
| + | * be sure the input files are called " | ||
| + | * if you want to compare the bias/ | ||
| + | |||
| + | | ||
| + | | ||
| + | | ||
| + | |||
| + | * if you want to compare the bias/ | ||
| + | |||
| + | | ||
| + | | ||
| + | | ||
| ====Analog FED==== | ====Analog FED==== | ||
| Line 41: | Line 80: | ||
| ====pxFEC==== | ====pxFEC==== | ||
| + | |||
| Start the server: | Start the server: | ||
| + | |||
| cd TriDAS/ | cd TriDAS/ | ||
| | | ||
| | | ||
| + | Some commands: | ||
| + | * **exec data/ | ||
| + | * **cn +2PL12** : set control network (+2PL12 for layers 1-2 and +2PL3 for layers 3-4) | ||
| + | * **module 31** : set the module hub | ||
| + | * **roc 0:15** : set the ROCs you want to program | ||
| + | * **Vana 120** : program the ROCs registers (ex: Vana) | ||
| + | * **tbm reset** : reset the tbm | ||
| + | * **tbm disable triggers** (**tbm enable triggers**) : force no token passed mode (the tbm does not wait for the token to be returned) | ||
| + | * **tbm enablepkam** (**tbm disablepkam**) : the tbm is reset after a lapse of time in which it does not receive the token back | ||
phase1/phase1/bpixeltools.txt · Last modified: 2015/05/21 11:38 by ngadiuba
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
