<HwDescription>

  <AMC13>
      <connection id="T1" uri="chtcp-2.0://cmspixel2.physik.uzh.ch:10203?target=bpixamc13T1:50001" address_table="file://settings/AMC13XG_T1.xml" />
      <connection id="T2" uri="chtcp-2.0://cmspixel2.physik.uzh.ch:10203?target=bpixamc13T2:50001" address_table="file://settings/AMC13XG_T2.xml" />
      <AMCmask enable="1,2,3,4,5,6,7,8,9,10,11,12"/> <!--comma separated list of slots to which AMC13 signals are distributed: by default all-->
      <!--This is used to send a calibration Trigger via the AMC13s internal BGO mechanism, 0x2c is the command configured as BGO15 
           on the TTCci - repeat is obvious, prescale is in orbits, the bx is selected such that it occurs 98 BX before the local
           L1A which is periodic at BX500 every orbit-->
      <!-- for the DEV lab setup in B186, the bx has to be 381 for the BU clock source and 380 for the TTCci as clock source -->
      <BGO command="0x2c" repeat="1" prescale="1" bx="374" />
      <!--<BGO command="0x2e" repeat="0" prescale="0" bx="0" />-->
      <!-- Local enables Local L1A, mode 0 means a trigger every orbit at BX500, rate is 1 for every orbit and burst is 1 
           for 1 trigger when sending burst (equivalent to single trigger -->
      <Trigger local="1" mode="0" rate="1000" burst="1" rules="0" /> 
      <!--<Register tounge="T1" name="test.test">0</Register>-->
      <TTCSimulator>0</TTCSimulator>
  </AMC13>
  <PixFED Id="0" boardType="CTA">
      <connection id="board0" uri="chtcp-2.0://cmspixel2.physik.uzh.ch:10203?target=bpixfed1:50001" address_table="file://settings/address_table.xml" />

      <!-- ACQUISITION MODE & CALIBRATION MODE & DATA TYPE -->
      <!--1: TBM fifo, 2: Slink FIFO, 4: FEROL-->
      <Register name="pixfed_ctrl_regs.acq_ctrl.acq_mode">2</Register>
      <Register name="pixfed_ctrl_regs.acq_ctrl.calib_mode"> 0 </Register>
      <!--this is 0-indexed so 9 will correspond to 10 events-->
      <Register name="pixfed_ctrl_regs.acq_ctrl.calib_mode_NEvents"> 1 </Register>
      <!--0: real data, 1: constants after TBM fifo, 2: pattern before TBM fifo-->
      <Register name="pixfed_ctrl_regs.data_type">0</Register>

      <!--SLINK HEADER & TRAILER-->
      <Register name="pixfed_ctrl_regs.slink_ctrl.privateEvtNb">0x01</Register>
      <Register name="pixfed_ctrl_regs.slink_ctrl.slinkFormatH_source_id">0x01</Register>
      <Register name="pixfed_ctrl_regs.slink_ctrl.slinkFormatH_FOV">0xe</Register>
      <Register name="pixfed_ctrl_regs.slink_ctrl.slinkFormatH_Evt_ty">0xa</Register>
      <Register name="pixfed_ctrl_regs.slink_ctrl.slinkFormatH_Evt_stat">0xf</Register>

      <!-- TBM MASK -->
      <Register name="pixfed_ctrl_regs.TBM_MASK_1">0xFFFFFCFF</Register>
      <Register name="pixfed_ctrl_regs.TBM_MASK_2">0x0000FFFF</Register>
      <Register name="pixfed_ctrl_regs.tbm_trailer_status_mask">0x00</Register>
      <!--<Register name="pixfed_ctrl_regs.PACKET_NB">10</Register>-->

      <!--TTS CONFIG-->
<!-- to enable or disable timeout check & evnt cnt check: 0 disable, 1 enable -->
      <Register name="pixfed_ctrl_regs.tts.timeout_check_valid"> 1 </Register>
      <Register name="pixfed_ctrl_regs.tts.event_cnt_check_valid"> 1 </Register>
      <!--<Register name="pixfed_ctrl_regs.tts.timeout_value"> 255 </Register>-->
<!-- configure timeout threshold for TBM channels (FED channels) -->
      <Register name="pixfed_ctrl_regs.tts.evt_timeout_value.tbm_ch_02"> 255 </Register>
      <Register name="pixfed_ctrl_regs.tts.evt_timeout_value.tbm_ch_03"> 255 </Register>
<!-- OOS thresholds -->
      <Register name="pixfed_ctrl_regs.tts.evt_err_nb_oos_thresh"> 255</Register>
      <Register name="pixfed_ctrl_regs.tts.timeout_nb_oos_thresh"> 255 </Register>
      <Register name="pixfed_ctrl_regs.tts.bc0_ec0_polar"> 0 </Register>
<!-- set to 1 to force TTS state ready -->
      <Register name="pixfed_ctrl_regs.tts.force_RDY"> 0 </Register>

<!-- mask to filter error conditions, 0 filters everything, 0xFF lets everything through -->
      <!--Mask operation for the TBM trailer (STATUS1) STATUS1(7:0) = [NoTokenPass - ResetTBM - ResetROC - SyncError - SyncTrigger - ClrTrigCnt - CalTrig - Stackful] Masked or not with trailer_status_mask1[7:0]-->
      <Register name="pixfed_ctrl_regs.tbm_trailer_status_mask"> 0xFF </Register>
      <!--Mask operation for the TBM trailer STATUS2 or ERR_BITS STATUS2(2:0) = [WrongNbOfROCs - AutoResetSent - PKAMReseSent] Masked or not with trailer_status_mask2(2:0)-->
      <Register name="pixfed_ctrl_regs.tbm_trailer_status_mask2"> 1 </Register>

      <!--CLOCK-->
      <!--Used to set the CLK input to the TTC clock from the BP - 3 is XTAL, 0 is BP-->
      <Register name="ctrl.ttc_xpoint_A_out3">0</Register>
      <!--<Register name="ctrl.mgt_xpoint_out1">3 </Register>-->
      <!--2 to have 156 MHz clock (obligatory for 10G sling), 3 for 125Mhz clock for 5g on SLink -->
      <Register name="ctrl.mgt_xpoint_out1">3 </Register>

      <!-- FITELS -->
      <Fitel_Files path="./settings/" />
      <Fitel FMC="0" Id="1" file="FMCFITEL.txt" Enable="5,6" />
      <Fitel FMC="0" Id="0" file="FMCFITEL.txt" Enable="" />
  </PixFED>

</HwDescription>

<Settings>

  <!-- 0 indexed -->
  <Setting name="ChannelOfInterest">4</Setting>
  <!-- 0 indexed -->
  <Setting name="ROCOfInterest">1</Setting>
  <Setting name="BlockSize">512</Setting>
  <!--if set to 0, loop will run forever-->
  <Setting name="NAcq">0</Setting>

</Settings>